Vermont DMV CDL General Knowledge Practice Test 9
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. Some commodities have their own detailed securement rules on top of the general ones. Which list is made up of such commodities?
Show answer
Answer C: Logs, metal coils, paper rolls, concrete pipe and crushed vehicles
The cargo securement rules add specific requirements for particular commodities, including logs, dressed lumber, metal coils, paper rolls, concrete pipe, intermodal containers, vehicles, crushed cars, roll on containers and large boulders.
-
2. You are hauling a sealed trailer and have been told in writing not to open it. How does that affect the en route cargo checks?
Show answer
Answer C: You do not have to inspect the cargo itself, but the vehicle and weight are still yours
The en route cargo inspection rule does not apply to a driver of a sealed vehicle who has been ordered not to open it, but every other responsibility, including legal weight, remains.
-
3. A driver hauling a sealed trailer that cannot be opened is still responsible for what?
Show answer
Answer D: Making sure the rig is not over the gross or axle weight limits
A seal prevents inspecting the contents, but the driver must still confirm the vehicle is not overloaded.
-
4. A hard frost has left your vehicle covered in ice. What must be cleared before you drive?
Show answer
Answer D: The windshield, mirrors, lights and reflectors
You must be able to see out and other drivers must be able to see your lights and reflectors, so all of those surfaces have to be cleared.
-
5. You press on a drive belt and it deflects far more than the others. What does that suggest?
Show answer
Answer C: The belt is too loose and the part it drives may not work properly
A belt with excessive play slips on its pulleys, so the accessory it drives turns too slowly or not at all under load.
-
6. A dock crew loads and straps the freight. Who is responsible for the load being legal and secure on the road?
Show answer
Answer D: The driver
Even when someone else loads and secures the freight, the driver must inspect it and remains responsible for it while driving.
-
7. Why should high beams not be used in fog?
Show answer
Answer A: The light reflects back off the droplets and blinds you
Fog is made of water droplets that scatter light straight back at the driver, so a stronger beam makes the wall of glare worse rather than better.
-
8. You are pulling away from the curb after a delivery. Why is a mirror check needed first?
Show answer
Answer B: A cyclist or a vehicle may be coming up alongside you
Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.
-
9. You are hauling a load of steel plate that is well within every weight limit but is stacked five feet high on a flatbed. What is the main concern?
Show answer
Answer A: The center of gravity is high, so the rig will roll more easily in a curve
Legal weight does not make a load safe; height raises the center of gravity and it is height, not weight alone, that decides how readily the vehicle rolls over.
-
10. Rust streaks are running outward from the lug nuts on one wheel. What does this most likely indicate?
Show answer
Answer C: The lug nuts may be loose
Rust trails spreading from the nuts are a classic sign that the nuts have worked loose and the wheel has been moving on the studs.
-
11. Where are regrooved, recapped or retreaded tires not allowed on a truck or truck tractor?
Show answer
Answer C: On the front steering wheels
Regrooved and retreaded tires are prohibited on the front wheels of a truck or truck tractor because a steering tire blowout is extremely difficult to manage.
-
12. Which clues warn you that a parked car may pull out or open a door?
Show answer
Answer A: Exhaust smoke, turned front wheels, a person in the seat
Signs of life in a parked vehicle, such as a running engine, turned wheels or an occupant, mean it may move or open a door into your path.
-
13. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
14. Taking your eyes off the road for about five seconds at highway speed means traveling roughly how far unseen?
Show answer
Answer A: About the length of a football field
At highway speed a five second glance away covers roughly 100 yards, which is far more road than any driver can afford to travel blind.
-
15. You are taking a tightly curved highway exit ramp in a long combination. Where should the tractor be placed within the lane?
Show answer
Answer D: Toward the outside of the curve, leaving room for the trailer to track inside
Because the trailer wheels cut to the inside of the curve, the tractor has to be kept out toward the outer edge so the trailer does not drop a wheel off the inside edge.
-
16. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?
Show answer
Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic
Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.
-
17. Why should both outside mirrors be checked over and over while backing?
Show answer
Answer B: Each mirror covers only part of the path and neither covers the blind spots, so people and objects can appear without warning
Working both mirrors in turn is the only way to follow the whole path of a vehicle you cannot see behind.
-
18. Why are the windshield wipers on the pre-trip list even before a trip in fine weather?
Show answer
Answer C: Because weather can change and a wiper failure leaves the driver without a clear view
Rain, spray or mud can arrive at any point in a long trip, and a wiper that fails then leaves the driver with no way to clear the windshield.
-
19. What happens to braking distance when speed is doubled?
Show answer
Answer C: It becomes about four times longer
Braking distance grows with the square of speed, so doubling the speed multiplies both the braking distance and the force of an impact by about four.
-
20. Compared with a fully loaded one, an empty truck under hard braking will often do what?
Show answer
Answer A: Need a longer distance to stop because traction is poor
Stiff suspension and little weight over the tires reduce grip, so the wheels lock early and the vehicle can take longer to stop.
-
21. You are on a freeway and see brake lights come on in several vehicles far ahead of you. What should you do?
Show answer
Answer A: Ease off the accelerator and get ready to slow down
Brake lights well ahead are an early warning that traffic is slowing, and acting on them gives a heavy vehicle the room it needs.
-
22. Why should you never shift gears while crossing railroad tracks?
Show answer
Answer A: You could miss the gear or stall and be stuck on the tracks
A stalled or coasting vehicle on the tracks has no way to clear quickly, so choose the gear before the crossing and do not shift until you are across.
-
23. A strap runs from an anchor point on one side of the trailer, over the load, and down to an anchor point on the opposite side. How much of its working load limit counts toward the total required?
Show answer
Answer C: All of it
A tiedown that is anchored on one side, passes over or around the cargo and is anchored on the other side counts its full working load limit toward the aggregate figure.
-
24. How should the headlamps be checked during the pre-trip inspection?
Show answer
Answer A: By switching on both low beam and high beam and confirming each one works outside
Both beams are separate circuits, so each is switched on in turn and confirmed from outside the vehicle where the lamps can actually be seen.
-
25. You have backed into the same loading bay every week for a year. How often should you still get out and walk to the rear before backing?
Show answer
Answer D: Every time, since the area can change while you are away from it
A familiar space is no guarantee; vehicles, pallets, people and overhead obstructions appear between one visit and the next, so you check on every occasion.
-
26. What should you check about the air hoses and the electrical cord running to the trailer?
Show answer
Answer D: That they are free of damage, properly connected and not dragging or rubbing
Lines that chafe on the frame or drag on the road wear through, and a broken line takes away trailer braking or trailer lighting without warning.
-
27. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
28. What is the purpose of the torque rods or radius rods you check on the suspension?
Show answer
Answer A: They hold the axle in alignment with the frame under braking and acceleration
Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.
-
29. Under federal rules, what happens to a commercial driver found with any detectable amount of alcohol while operating a commercial vehicle?
Show answer
Answer D: The driver is placed out of service for 24 hours
Any measurable alcohol takes a commercial driver off the road for 24 hours, and a concentration of 0.04 percent or more brings a disqualification.
-
30. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.
-
31. Who may remove an out-of-service sticker from a commercial vehicle?
Show answer
Answer B: Only an authorized person, and only after the defect that caused it has been repaired
The sticker stays on the vehicle until the repairs are made and an authorized person removes it, so nobody can simply peel it off and drive away.
-
32. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
33. Which components on a typical engine are driven by belts that must be checked for wear and tension?
Show answer
Answer D: The alternator, the water pump and, on many vehicles, the air compressor
Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.
-
34. Cargo falls from your trailer and causes a crash behind you. Who is likely to answer for it?
Show answer
Answer C: The driver and the carrier, since securing the load on the road is their duty
Whoever loaded the vehicle, the driver and the carrier are responsible for the load being secure while it is on the road.
-
35. You have chosen 40 miles per hour as your safe speed for a downgrade. How should the brakes be used?
Show answer
Answer A: Brake firmly to about 35, release, and repeat at 40
Proper technique is firm application to about 5 miles per hour below the safe speed, then full release so the brakes cool before the next application.
-
36. A car that passed you on the right slows and stays alongside your trailer. What is the best response?
Show answer
Answer D: Ease off the accelerator so the car can move clear
A vehicle sitting beside a trailer is in a blind area and has nowhere to go if you need the lane, so the safest fix is to let it get ahead or behind.
-
37. Federal rules require a power unit that is not carrying placarded hazardous materials to have a fire extinguisher with which minimum rating?
Show answer
Answer A: One rated 5 B:C or more, or two rated 4 B:C or more each
The minimum is a single unit rated 5 B:C or more, or two units of at least 4 B:C each, which is enough to attack a fuel or electrical fire.
-
38. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
39. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
40. What is the risk when too little weight rests on the drive axles?
Show answer
Answer A: Poor traction, so the drive wheels spin easily on wet or slippery surfaces
Traction depends on weight pressing the driving tires onto the road, so a light drive axle spins on wet, snowy or loose surfaces.
-
41. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?
Show answer
Answer A: Shift up as road speed rises, so engine braking falls away
An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.
-
42. With the tractor coupled to the trailer, what should you see between the upper and lower fifth wheel plates?
Show answer
Answer A: No space at all between the two plates
Any daylight between the plates means the trailer is not properly seated on the fifth wheel and the coupling can come apart under load.
-
43. Why is driving much slower than the rest of the traffic dangerous?
Show answer
Answer B: Other drivers must keep passing you, which creates conflicts
Traffic that has to work its way around you produces lane changes and closing speeds, which is why a large speed difference is itself a hazard.
-
44. Why should a retarder be switched off when the road is wet, icy or snowy?
Show answer
Answer C: It can make the drive wheels skid when traction is poor
A retarder slows the drive wheels only, and on a slippery surface that braking force can break their traction and start a skid.
-
45. Where on a tire is tread depth measured?
Show answer
Answer C: In a major tread groove, away from any tie bar or wear indicator
Depth is taken in a major groove and away from the raised tie bars and wear indicators, which would give a shallower and misleading reading.
-
46. In the seven-step method, what comes immediately after starting the engine and inspecting inside the cab?
Show answer
Answer D: Turn off the engine and check the lights
Step four shuts the engine down and switches on the lamps needed for driving so the driver can leave the cab and confirm they actually work.
-
47. What does the federal bridge formula do?
Show answer
Answer C: It reduces the weight allowed on a group of axles as those axles get closer together
Axles bunched together concentrate the load on a short span of a bridge, so the formula lowers the allowable weight as the spacing shrinks.
-
48. You are hauling livestock and the trailer is only partly full. What should be done?
Show answer
Answer A: Use false bulkheads or partitions to keep the animals bunched together
Animals that can move around shift the center of gravity, so a partial load is bunched together with partitions to limit how far the weight can move.
-
49. A load overhangs the rear of the trailer. What must the driver check before leaving?
Show answer
Answer D: That the overhang is marked as required, with flags or lamps as conditions demand
A projecting load has to be made visible to other drivers, with flags in daylight and lamps when lights are required, so nobody runs into what they cannot see.
-
50. When must a driver first inspect the cargo and its securement devices?
Show answer
Answer C: Before starting the trip, as part of the pre-trip inspection
Cargo is part of the pre-trip inspection; the later checks within 50 miles and every three hours or 150 miles come on top of that first inspection.