Vermont DMV CDL General Knowledge Practice Test 5
Test 5 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Vermont test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. A fire has started in the vehicle. How should the extinguisher be used?
Show answer
Answer B: Stay as far back as the reach of the extinguisher allows, stand upwind, and aim at the base of the fire
Aiming at the base attacks what is actually burning, and staying upwind and well back protects the driver from heat, smoke and the flames themselves.
-
2. What must a written driver vehicle inspection report cover at the end of the day?
Show answer
Answer C: Any defect or deficiency that would affect safety or could cause a mechanical breakdown
The report identifies the vehicle and lists defects that affect safe operation or could lead to a breakdown, so they are repaired before the next trip.
-
3. How does a driver measure following distance in seconds?
Show answer
Answer A: Wait for the vehicle ahead to pass a fixed roadside object, then count the seconds until the front of your vehicle reaches the same object
Counting from the moment the vehicle ahead passes a landmark until you reach it turns a gap you cannot judge in feet into a number of seconds.
-
4. Which of these is a major cause of skids in heavy vehicles?
Show answer
Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions
Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.
-
5. How does the working load limit of a tiedown relate to the force that would break it?
Show answer
Answer B: The working load limit is a fraction of the breaking strength and is the figure you use
The working load limit is set well below the point at which the device would fail, and securement is always calculated from the working load limit, never from breaking strength.
-
6. You are given a ratchet strap with a deep cut along one edge. What should you do?
Show answer
Answer C: Do not use it; a damaged tiedown cannot be relied on to hold its rated load
Cuts, burns, knots and broken stitching weaken a strap far below its marked working load limit, so it must be taken out of service.
-
7. What is the purpose of the torque rods or radius rods you check on the suspension?
Show answer
Answer A: They hold the axle in alignment with the frame under braking and acceleration
Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.
-
8. Federal rules say a commercial vehicle may not be driven unless what is true of its cargo?
Show answer
Answer B: It is properly distributed and adequately secured
The basic federal requirement is that the load be distributed properly and secured well enough that it cannot move, whatever the paperwork says.
-
9. What is the correct order for a basic double clutch upshift?
Show answer
Answer B: Release the accelerator and push the clutch, shift to neutral, release the clutch, let engine speed drop, push the clutch again and shift to the higher gear
Double clutching passes through neutral with the clutch released so engine speed can drop to match the next gear before it is engaged.
-
10. What does the tachometer on the dashboard of a heavy truck show?
Show answer
Answer D: How fast the engine is turning, in revolutions per minute
The tachometer reads engine speed in rpm, which is what a driver uses to judge shift points in a vehicle with a manual transmission.
-
11. What should you check about the air hoses and the electrical cord running to the trailer?
Show answer
Answer D: That they are free of damage, properly connected and not dragging or rubbing
Lines that chafe on the frame or drag on the road wear through, and a broken line takes away trailer braking or trailer lighting without warning.
-
12. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?
Show answer
Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it
Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.
-
13. What must be true of the person who performs the annual periodic inspection?
Show answer
Answer D: They must meet the federal qualification requirements for an inspector
The inspection has to be done by someone who meets the federal training and experience requirements for inspectors, whoever employs them.
-
14. How do you confirm that the coupling is locked before pulling out of the yard?
Show answer
Answer D: By locking the trailer brakes and pulling gently forward against them
The tug test loads the coupling in the direction that would pull it apart, so if the jaws are not closed on the kingpin you find out at walking pace.
-
15. An article of cargo has been blocked so that it cannot move forward. How many tiedowns does the federal rule call for?
Show answer
Answer A: One tiedown for every 10 feet of article length, or any part of that
Blocking against forward movement lowers the requirement to one tiedown per 10 feet of length or fraction of 10 feet.
-
16. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?
Show answer
Answer B: Make every steering, braking and speed change gradual
Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.
-
17. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
18. Before starting a trip, what must the driver confirm about the weight of the loaded vehicle?
Show answer
Answer A: That it is within the legal gross and axle limits for the route being driven
Overweight vehicles brake poorly, damage tires and suspension components, and can be put out of service at a scale, so weight is checked before the wheels turn.
-
19. In the seven-step method, what comes immediately after starting the engine and inspecting inside the cab?
Show answer
Answer D: Turn off the engine and check the lights
Step four shuts the engine down and switches on the lamps needed for driving so the driver can leave the cab and confirm they actually work.
-
20. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
21. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
22. Why do cracked spring hangers or badly worn shackles matter?
Show answer
Answer A: They allow the axle to shift out of its correct position under the vehicle
Hangers and shackles hold the spring, and therefore the axle, in place, so when they fail the axle can move and the vehicle may become uncontrollable.
-
23. Who must sign a driver vehicle inspection report?
Show answer
Answer D: The driver who prepared it
The report is the driver statement about the condition of the vehicle at the end of the day, so the driver signs it.
-
24. Why should you avoid using your lights to tell a following driver that it is safe to pass you?
Show answer
Answer B: You may misjudge the gap and the driver will act on your signal
The manual warns against signaling others to pass, because the responsibility for a head-on crash then rests on a judgment you could easily get wrong.
-
25. How do you test for leaks in a hydraulic brake system during the pre-trip inspection?
Show answer
Answer A: Pump the pedal three times, then hold firm pressure for five seconds and make sure the pedal does not move
If the pedal sinks while you hold pressure, fluid is escaping or air is in the lines, and the vehicle must not be driven until the problem is repaired.
-
26. Why should the radio, the fan and other noisy equipment be switched off during a required stop at a railroad crossing?
Show answer
Answer C: So that an approaching train can be heard
The rules require the driver to look and listen along the track, and on a double track crossing a passing train can hide a second one, so hearing matters as much as seeing.
-
27. You are dropping a loaded trailer in a yard. How far should the landing gear be lowered?
Show answer
Answer A: Until the pads make firm contact and the trailer weight is just off the fifth wheel
Cranking down until the gear is firmly on the ground and just lifting the load off the fifth wheel makes the trailer stable and lets the tractor pull out cleanly.
-
28. What should you check about the fuel tank during the walkaround?
Show answer
Answer A: That it is securely mounted, the cap is on tight and there are no leaks
A loose tank or a missing cap can spill fuel, and any fuel leak is a fire hazard that makes the vehicle unsafe to drive.
-
29. What alcohol concentration makes it illegal for a person to operate a school bus in Vermont?
Show answer
Answer D: 0.02 or more
Vermont sets a 0.02 alcohol concentration threshold for a person operating a school bus, far below the 0.08 threshold used for ordinary drivers.
-
30. What alcohol concentration makes it illegal to operate a commercial motor vehicle in Vermont?
Show answer
Answer A: 0.04 or more
Vermont sets the alcohol concentration limit for operating a commercial motor vehicle at 0.04, half the limit that applies to noncommercial drivers.
-
31. Why should water never be used on an electrical fire or a gasoline fire?
Show answer
Answer C: It spreads the fuel and conducts the current
Water carries current back to the person holding the hose and floats burning fuel outward, which is why a B:C rated extinguisher is carried instead.
-
32. A brake light lens is cracked and the lamp still lights. How should that be treated?
Show answer
Answer B: As a defect, because water can enter and the lamp can dim or fail
A cracked lens lets in water and dirt, which corrodes the socket and dulls the lamp, so it is reported before it becomes a dead brake light.
-
33. Which of these is a suspension defect you must look for during the walkaround?
Show answer
Answer D: Cracked or broken spring leaves, loose or broken U-bolts, or leaking air suspension bags
Broken springs, failed U-bolts and leaking air bags let the axle shift or the body drop, which can make the vehicle impossible to control.
-
34. You need to check your route on a navigation device. What is the correct approach?
Show answer
Answer D: Set it before the trip or after you have parked
Route programming is planning work, and it belongs to the time before the wheels turn or after the vehicle is safely parked off the roadway.
-
35. A fire starts in the cargo area of a van trailer. Why should you keep the doors closed until firefighters arrive?
Show answer
Answer D: Opening the doors lets in air that feeds the fire
A fire in a closed van is starved of oxygen; opening the doors gives it the air it needs to flare up.
-
36. Cargo falls from your trailer and causes a crash behind you. Who is likely to answer for it?
Show answer
Answer C: The driver and the carrier, since securing the load on the road is their duty
Whoever loaded the vehicle, the driver and the carrier are responsible for the load being secure while it is on the road.
-
37. Which parts of total stopping distance can a driver shorten simply by staying alert and looking far ahead?
Show answer
Answer B: Perception distance and reaction distance
Alertness shortens the time spent recognizing a hazard and moving your foot to the pedal; braking distance depends on speed, weight, brakes and the road surface.
-
38. On a two lane road carrying traffic in both directions, where do the three warning devices go?
Show answer
Answer C: About 10 feet from the vehicle on the traffic side, 100 feet behind and 100 feet ahead
Traffic can approach from either direction, so one device goes close to the vehicle and one is placed about 100 feet away in each direction.
-
39. Why should a retarder be switched off when the road is wet, icy or snowy?
Show answer
Answer C: It can make the drive wheels skid when traction is poor
A retarder slows the drive wheels only, and on a slippery surface that braking force can break their traction and start a skid.
-
40. During a stop you find a package in the trailer leaking an unknown chemical. What should you do?
Show answer
Answer C: Keep clear, keep others away and get help without touching the package
A driver without the training and equipment does not handle a leak; the job is to protect people from the material and get qualified help to the scene.
-
41. What are the rules for using your turn signal before a turn or lane change?
Show answer
Answer A: Signal early, keep the signal on until the turn is finished, then cancel it
An early, continuous signal tells others what you plan to do; cancelling afterward keeps the signal from misleading them.
-
42. Why does a load of live animals need special attention?
Show answer
Answer D: The animals move and lean, so the center of gravity shifts and the vehicle can be pushed off balance in a turn
A live load will not stay where it is put, and that movement changes the balance of the vehicle exactly when a curve is loading it most.
-
43. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
44. What is the coupling device weight rating on a vehicle?
Show answer
Answer A: The most weight that the coupling on the vehicle is rated to pull
The coupling device rating is a limit on how much weight the coupling may tow, and it is one of the ratings that has to be respected when a combination is loaded.
-
45. What is a bulkhead in a cargo body used for?
Show answer
Answer D: To divide the space and stop cargo from moving into another part of the body
A bulkhead is a solid partition that separates one part of the load space from another and blocks the cargo from moving past it.
-
46. Why should a driver avoid stopping partway up a snow covered hill?
Show answer
Answer D: You may not get moving again and could slide backwards
On a slippery grade the drive wheels may simply spin when you try to restart, leaving the vehicle stuck across the road or sliding back down it.
-
47. A hard frost has left your vehicle covered in ice. What must be cleared before you drive?
Show answer
Answer D: The windshield, mirrors, lights and reflectors
You must be able to see out and other drivers must be able to see your lights and reflectors, so all of those surfaces have to be cleared.
-
48. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?
Show answer
Answer A: 5 seconds
One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.
-
49. What are you looking for when you check the drive belts in the engine compartment?
Show answer
Answer C: That each belt is snug and free of cracks, frays or heavy wear
A loose or cracked belt can break and stop the fan, the water pump or the alternator, which leads quickly to overheating or a dead electrical system.
-
50. A driver behind you wants to pass and you can see that the road ahead is clear. What should you do?
Show answer
Answer B: Do not signal the other driver to pass; let that driver decide when it is safe
Directing other drivers can cause a crash if you misjudge the gap, so leave the decision to the driver who is passing.